Fault code group
Catalytic converter Fault Codes
The catalytic converter turns carbon monoxide, hydrocarbons and nitrogen oxides in the exhaust into less harmful gases. On petrol engines the control unit usually checks its efficiency by comparing the signals of the lambda sensors before and after it, and stores a fault code when efficiency drops below the threshold. On diesel engines the oxidation catalyst (DOC) may also fall into this group.
System
What does this system do?
The catalytic converter turns carbon monoxide, hydrocarbons and nitrogen oxides in the exhaust into less harmful gases. On petrol engines the control unit usually checks its efficiency by comparing the signals of the lambda sensors before and after it, and stores a fault code when efficiency drops below the threshold. On diesel engines the oxidation catalyst (DOC) may also fall into this group.
A fault code is a symptom; on its own it does not tell you the cause. First check live data with a diagnostic tool and inspect wiring, connectors and components. A software operation does not replace fault diagnosis and repair.
Code search
Look up a fault code
If the code has its own page you go straight to it; if it is only listed in a group table you go to its row.
Code list
Catalytic converter fault codes
| Description | Code |
|---|---|
| Catalyst System Efficiency Below Threshold (Bank 1) | P0420 |
| Warm Up Catalyst Efficiency Below Threshold (Bank 1) | P0421 |
| Main Catalyst Efficiency Below Threshold (Bank 1) | P0422 |
| Heated Catalyst Efficiency Below Threshold (Bank 1) | P0423 |
| Heated Catalyst Temperature Below Threshold (Bank 1) | P0424 |
| Catalyst Temperature Sensor (Bank 1 Sensor 1) – Circuit | P0425 |
| Catalyst Temperature Sensor (Bank 1 Sensor 1) – Range/Performance | P0426 |
| Catalyst Temperature Sensor (Bank 1 Sensor 1) – Circuit Low | P0427 |
| Catalyst Temperature Sensor (Bank 1 Sensor 1) – Circuit High | P0428 |
| Catalyst Heater Control (Bank 1) – Circuit/Open | P0429 |
| Catalyst Temperature Sensor (Bank 1 Sensor 2) – Circuit | P042A |
| Catalyst Temperature Sensor (Bank 1 Sensor 2) – Range/Performance | P042B |
| Catalyst Temperature Sensor (Bank 1 Sensor 2) – Circuit Low | P042C |
| Catalyst Temperature Sensor (Bank 1 Sensor 2) – Circuit High | P042D |
| Catalyst System Efficiency Below Threshold (Bank 2) | P0430 |
| Warm Up Catalyst Efficiency Below Threshold (Bank 2) | P0431 |
| Main Catalyst Efficiency Below Threshold (Bank 2) | P0432 |
| Heated Catalyst Efficiency Below Threshold (Bank 2) | P0433 |
| Heated Catalyst Temperature Below Threshold (Bank 2) | P0434 |
| Catalyst Temperature Sensor (Bank 2 Sensor 1) – Circuit | P0435 |
| Catalyst Temperature Sensor (Bank 2 Sensor 1) – Range/Performance | P0436 |
| Catalyst Temperature Sensor (Bank 2 Sensor 1) – Circuit Low | P0437 |
| Catalyst Temperature Sensor (Bank 2 Sensor 1) – Circuit High | P0438 |
| Catalyst Heater Control (Bank 2) – Circuit/Open | P0439 |
| Catalyst Temperature Sensor (Bank 2 Sensor 2) – Circuit | P043A |
| Catalyst Temperature Sensor (Bank 2 Sensor 2) – Range/Performance | P043B |
| Catalyst Temperature Sensor (Bank 2 Sensor 2) – Circuit Low | P043C |
| Catalyst Temperature Sensor (Bank 2 Sensor 2) – Circuit High | P043D |
| Catalyst Temperature Sensor 1/2 (Bank 1) – Correlation | P046A |
| Catalyst Temperature Sensor 1/2 (Bank 2) – Correlation | P046B |
| Catalyst Heater (Bank 1) – Supply Voltage | P04F2 |
| Catalyst Heater (Bank 2) – Supply Voltage | P04F3 |
| Catalyst Heater (Bank 1) – Circuit Low | P04F4 |
| Catalyst Heater (Bank 2) – Circuit Low | P04F5 |
| Catalyst Heater (Bank 1) – Circuit High | P04F6 |
| Catalyst Heater (Bank 2) – Circuit High | P04F7 |
| Catalyst Heater (Bank 1) – Intermittent | P04F8 |
| Catalyst Heater (Bank 2) – Intermittent | P04F9 |
| Catalyst Heater (Bank 1) – Performance | P04FE |
| Catalyst Heater (Bank 2) – Performance | P04FF |
| HC Adsorption Catalyst Efficiency Below Threshold (Bank 1) | P2423 |
| HC Adsorption Catalyst Efficiency Below Threshold (Bank 2) | P2424 |
Linked codes have their own page; the others are listed in this table only.
Related operations
Software operations related to this system
Help
Frequently asked questions
What do Catalytic converter fault codes indicate?
The catalytic converter turns carbon monoxide, hydrocarbons and nitrogen oxides in the exhaust into less harmful gases. On petrol engines the control unit usually checks its efficiency by comparing the signals of the lambda sensors before and after it, and stores a fault code when efficiency drops below the threshold. On diesel engines the oxidation catalyst (DOC) may also fall into this group.
Does switching off a fault code fix the fault?
No. Switching a code off in software does not remove the cause of the fault. Diagnose and repair the fault first. Operations on emission systems such as DTC off are offered only for use permitted by local law (e.g. off-road / motorsport / export).
Where do the code descriptions on these pages come from?
The code titles are based on the generic SAE J2012 / ISO 15031-6 code definitions and written in our own words. Manufacturer-specific codes are not listed. The ECU families come from fault code tables verified in EcuPrime.
Start today
A free account for dealers and tuning pros: upload your file, see which operations work, apply your solution.
Create free account